中心块调整工具（Central adjustment tool）
[此贴子已经被作者于2006-3-9 21:49:39编辑过]
| - What is a central adjustment of the Rubik's Cube?It is not done that this is done, and there is a considerable difference in the turning condition though it seems that it is most of one. (^^; From "It is not. ". it is easy ..new article.. to turn even if a lot of cubes are bought(^^;; | |
| Then, it is necessary to become complete the installation condition of 6 and a central cube though it is What is the cube per "" though it is the lowest for the time being. Of course, in most cases when you buy a new cube though there is Bali in the cube or Moromoro｢?..only this respect.. awfully rotating is ..heavy... ｣It becomes it. (^^; The reason for a central cube in the respect is that it is held down of Kitsc in case of such a case compared with other central cubes. ..(.. ..cry..) | |
|
- The installation condition of six central cube in Wake was evenly made an adjusted thing. (^^) If this is not done, not coming off is a central bolt though it is a central adjustment tool of making by oneself. ..(.. sweat | |
[此贴子已经被作者于2006-3-9 15:35:12编辑过]
Base board
It is a metallic board of the base that becomes foundation.
L character metal fittings(largeness)
It is L character metal fittings (largeness) that become the parts of the arm that pulls a central cube.
L character metal fittings(smallness)
It is small L character metal fittings to widen the suppression area of the suppressed central core side when a central cube is pulled.
The main bolt
It is a bolt of the main to pull a central cube.
Flange nut
It is loose Tots coming ..flange nut (..) that fixes the base board and L character metal fittings (largeness), etc.
M6 volt..(.. ..short..)
It is a short M6 volt that fixes the base board and L character metal fittings, etc.
M3 screw
It is a short screw to unite as for L character metal fittings (smallness).
M6 board nut
It becomes an applied part where the central core side is suppressed by previously installing it about the main bolt.
Whole chart
Back
From former
From post-
[此贴子已经被作者于2006-3-9 15:47:20编辑过]
|
First of all, both sides of a central cube are pulled. ｢The expansion condition is ..encounter.. ..,.. becoming it certainly different. ^^;｣It confirms. Is it the one that manages not to become though is so if it is said it is reluctant because and a central bolt are the driving types?..(.. ..cry..) |
|||
| Beforehand as such, it thinks where how much is pulled out at this time. How much?.....Suitably. (^^; There is Moromoro though it actually expresses numerically. | |||
L character class
L character metal fittings (smallness) are united as shown in the above figure. Only one side is fixed at this time so that opening and shutting is possible. The tightening condition is also suitable. (^^;
[此贴子已经被作者于2006-3-9 15:49:54编辑过]
L character class is set.
L character class is set in central parts as shown in the above figure. The purpose of this is to widen the bearing area of *) ..board nut (...
- Central parts that set L character class are set in the central adjustment tool.
[此贴子已经被作者于2006-3-9 15:52:15编辑过]
- Then, the center is adjusted.
It becomes the work of sober Japanese syllabary-. (^^;
A hex-head wrench that turns the main bolt is prepared. It is an easy Chin duck when there are two kinds as showing in the photograph.
It is easy to turn even if the angle has adhered because a hex-head wrench of the driver type is a type to which the point has rounded.
It is Shicnesgage. It is a tool to measure the area of the space chiefly. The numerical value doesn't serve as a reference slightly in Barebare. (^^;
It is Spana to tighten the hex nut. Any one is O.K . However, the thin one is good as such.
The entire how to take a stance becomes such feeling. Spana is turned by the right hand with the whole by the left hand actually.
Botiboti clears up in Spana while fixing the main bolt with a hex-head wrench when tightening it and a central cube is pulled. (^^)
Six corner nut that encounters and is trained to the main bolt of two , is tightened taking the place alternatively little by little with Botiboti. When only one side is tightened at a dash, it is dangerous. (^^;
Then, it becomes anyway the same pull omission condition as six by using Shicnesgage. Any measurement tool is good because the thickness pulled out is decided when doing. (^^)
|
- Then, it sees ..how much was able to be pulled out... Finally, six rubber doughnuts enter both, and it is independent in the place where the rotation lightens. (^^) (It still takes time to receive in season. ^^;) | |||
|
- I am processing accident Pop to most main cubes putting the rubber doughnut with a similar central adjustment though it is work that time Hima hangs considerably by feeling. m(_ _)m | |||
|
However, ･･･ The DIY kit is being sold now, and the central adjustment tool on this page ･･･ :. There seems to be no necessity any longer. (^^; |
[此贴子已经被作者于2006-3-9 17:11:52编辑过]
First of all, the vise is prepared. A medium size is good. (..melting.. .. match it or two desks^^;)
It is six corner nut of M8 used to support central parts. (Anything is good if there is thickness. ^^;)
Six corner nut is fixed to the vise with the vinyl tape etc.
Central parts were put on the vise. (It is exaggerated. ^^;)
It is a bolt used when crowding the strike of a central bolt. It is what is suitably lying in the vicinity. (^^;
When it is the one that covers the head of a central bolt, any bolt for driving is O.K like the above figure . .
[此贴子已经被作者于2006-3-9 17:15:16编辑过]
It takes a stance like this and it beats with the hammer on.
A central bolt bends if large in question is not driven here considerably serious and straight. (^^;
From central pulling out work When becoming it so . . . to the re-doing. ....(.. ..largeness.. cry.. !)
- Omake (^^;* that cannot be recommended so much
|
- In this page, it introduces the strategy that pulls out a central cube with a central adjustment tool. It is possible to pull it out with nippers though it got as shown in a left photograph. However, there are some problems. (^^; ･It doesn't come off if it is not power by cutting to strike a central bolt. ･Because it is not easy to take allowances for power, the possibility of pulling it out too much is large. ･It is easy to bend a central bolt because how to apply power to place with nippers is from a diagonal. ･The contact part of a central cube and central Paul (= central core) is transformed. | |
|
- It is because being able to write the thing very much also experiences them ･･･ I :. (^^;;; | |
其中下面的“球头内六角螺丝刀”拧内六角螺丝特别方便，在仪器等内部地方很小的场合，该螺丝刀不必与螺丝准直，歪很大的角度都照样拧！有公制、英制两种规格，互不通用！
工具是不错的，而且是新的，，
老大的拔钉器，是什么样子的哦！？？
这么多工具去哪弄啊
| 欢迎光临 魔方吧·中文魔方俱乐部 (http://bbs.mf8-china.com/) | Powered by Discuz! X2 |