5阶顶层的棱块交换有什么公式总结么？

偶尔路过

这个参照高阶盲拧。其实多是三交换。
这种方法转数比先转中心的多。理论研究可以，实战就慢了。

乌木

<P>不求速度，逐个逐个复原心块，不妨用这公式，注意，它是三置换公式还有那个心块参与置换，你实验下来即知：</P>
<P>&nbsp;</P>
<applet code="de.pirzer.rubik.ProfessorPlayerApp.class" codebase=5 width="280" height="300">
  <param name="scrptLanguage" value="PirzerENG">
  <param name="scrpt" value="U MRR U' MLL' U MRR' U' MLL ">
  <param name="stickersFront" value="0,0,0,0,0,0,0,0,5,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0">
  <param name="stickersUp" value="5,5,5,5,5,5,0,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5">
</applet>

乌木

<P>噢，这个也必需：</P>
<P>&nbsp;</P>
<applet code="de.pirzer.rubik.ProfessorPlayerApp.class" codebase=5 width="280" height="300">
  <param name="scrptLanguage" value="PirzerENG">
  <param name="scrpt" value="MR U MRR U' MR' U MRR' U' ">
  <param name="stickersFront" value="0,0,0,0,0,0,0,5,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0">
  <param name="stickersUp" value="5,5,5,5,5,5,5,0,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5">
</applet>

乌木

<P>12楼情况也可这样，就和13楼做法一致了：</P>
<P>&nbsp;</P>
<applet code="de.pirzer.rubik.ProfessorPlayerApp.class" codebase=5 width="280" height="300">
  <param name="scrptLanguage" value="PirzerENG">
  <param name="scrpt" value="MRR U'  MLL' U MRR'U'MLL U   ">
  <param name="stickersFront" value="0,0,0,0,0,0,0,0,5,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0">
  <param name="stickersUp" value="5,5,5,5,5,5,5,5,0,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5">
</applet>

乌木

补充：12楼情况若要用14楼方法，事前要预调动一下，做好14楼公式后，需要时，再逆调动。

乌木

<P>举例：</P>
<P>&nbsp;</P>
<applet code="de.pirzer.rubik.ProfessorPlayerApp.class" codebase=5 width="280" height="380">
  <param name="scrptLanguage" value="PirzerENG">
  <param name="scrpt" value="U MRR U' MLL' U MRR' U' MLL \n U MFF' U MBB U'MFF U MBB'  U2 \n CR' U' MF' U MFF' U' MF U   MFF \n CR' U2 MFF' U MBB U' MFF U MBB' U \n CF' CU2 U' MRR U MLL' U' MRR' U MLL \n U2 MR U MRR U' MR' U MRR' U \n CR2 CU2 MRR U' MLL' U MRR' U' MLL \n MRR U' MR U MRR' U' MR' U2 \n CR U MRR U' MR U MRR' U' MR' ">
  <param name="stickersFront" value="0,0,0,0,0,0,0,4,5,0,0,0,0,1,0,0,1,0,0,0,0,0,0,0,0">
  <param name="stickersRight" value="1,1,1,1,1,1,5,0,4,1,1,3,1,1,1,1,1,1,2,1,1,1,1,1,1">
  <param name="stickersDown" value="2,2,2,2,2,2,2,2,1,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2">
  <param name="stickersBack" value="3,3,3,3,3,3,3,0,3,3,3,3,3,3,3,3,3,3,3,3,3,3,3,3,3">
  <param name="stickersLeft" value="4,4,4,4,4,4,0,4,4,4,4,4,4,1,4,4,4,4,4,4,4,4,4,4,4">
  <param name="stickersUp" value="5,5,5,5,5,5,0,5,5,5,5,5,5,5,5,5,5,5,1,5,5,5,5,5,5">
</applet>

乌木

16楼的方法原理详见http://bbs.mf8-china.com/viewthr ... p;extra=&page=2 的15楼等。