12 color Pyraminx Crystal官方解法

phoenias

由于附件超过要求，我就把官方解法的PDF慢慢给大家贴上来，原来是英文的教程，我也按我自己的理解少说两句，不对的还请大家指正，我发完前请不要跟帖，谢谢~~~
1. First layer corners
This is very easy, until the fifth piece:

If a corner is in place but twisted, then repeat this sequence of moves twice to rotate it anti-clockwise,
or four times for clockwise.
第一步是还原底层的五个角块，如果情况与图例相反，大家就向相反时针方向还原即可

phoenias

2. First layer edges
Bring the edge piece you want to insert to a location below the place you wish
to insert it, with the top face colour on top. Insert it as follows:
第二步，还原底层棱块，方法如下图，分两种情况讨论：

第一种：

phoenias

~~下面是第二种：

phoenias

Now turn over the Crystal so that the solved face is at the bottom.

3. Lower equator corners
It is very easy to put the five lower equator corners in their correct
locations. If one is in its correct place but needs to be twisted do this:

下面把顶层反过来当底层
第三步，还原中低层角块：
如果其位置正确，但是需要翻转，那么如下操作（也就是说先要将角块放置到正确位置）

phoenias

4. Upper equator corners
To insert any corner from the top layer into the upper equator, use the
following moves:
The same sequence can also be used to move a corner out of the upper equator and into the top layer.
Repeating the move sequence twice will twist a corner in the upper equator clockwise. Repeating it four
times twists it anti-clockwise.
第四步是中高层角块，如下操作（此法也可以将下面的角块移到顶层）

phoenias

5. Last layer corner orientation
Look at the last 5 corners, and see which colour they have in common. We
will twist them so that they all show that same colour in the top face.

Rotate the top layer so that one of the corners that
need twisting lies at the front. Do the following move
sequence TWICE to twist the corner anti-clockwise. This
is the same sequence as in step 1.
X2
Note that the three front corners in the equator will also get twisted by this. Don’t worry, as they will
get untwisted automatically when the top layer is correct. If the top layer corner needs an clockwise
twist, then do the sequence 4 times instead of twice.
Repeat the above for every twisted corner in the top layer. Take care not to rotate the whole crystal –
turn only the top layer to bring a twisted corner to the front, otherwise the equator corners become
scrambled.
第五步，还原顶层的角块，这步还原时候会移动中上层的角块，但是不用担心，只要在同一个方向操作，当顶层角块还原后，中上层刚刚动过的角块也会自动复原，操作如下：
（要将顶层方向不对的角块依次转到你选定破坏的中上层角块的正上方）
（如果顶层颜色在另一方向可按相反时针方向操作）
以下步骤做两次

[ 本帖最后由 phoenias 于 2009-1-21 16:22 编辑 ]

phoenias

角块还原完成
图：

phoenias

7. Lower and middle edges
If one of the five edge pieces in the top face belongs in the bottom layer
or in the equator, then you can turn the top layer to get to one of the 6
situations shown below.

If the edge piece you want to solve lies horizontal in the top layer, you can bring it to an upright position
with the moves shown below. It can then be solved as above.
下一步  还原中层的棱块：
按如下步骤操作即可（我总结基本就是两条，同向错开法，反向顶层翻转法）
分以下几种情况：
第一种：

phoenias

第二种和第三种：

phoenias

第四种和第五种：